Trapezoid Batting Cage Frame Kit 12' x 14' x 55' Heavy Duty Baseball/Softball

Baseball Batting Cage Frame Kit fits 12' x 14' x 55' Net. Note: The Legs should be staked or anchored down in areas where there is a possibility of moderate to high wind. Durable 1 1/2 steel frame corners. All hardware to hang your net. Our 55' x 12' x 14' - 1 1/2 frame corner kit is the most economic way to hang a batting cage net in any open space.

Kit comes with everything you need to assemble except the poles. Lowes Sku#-72717 or Home Depot Sku#-580023 (1 1/4 thin walled EMT Pipe). We are a family business started by my grandfather over 50 years ago. We intend on being in business for another 50 years.

We only sell quality, well made products. Note: The Batting Cage Net & 1 1/4 EMT poles are NOT included with this frame kit. Kit Includes the Following Parts.

(A) 3-Way Corners 4 pcs. (B) 4-Way Corners 6 pcs.

(H) Net Hangers 43 pcs. (I) Pipe End Caps 10 pcs. (J) Self-Drilling Screws 28 pcs. (K) 18' Tie Down Ropes 4 pcs. (L) Rope Stakes 4 pcs.

Kit Does NOT Include the Following Parts. (CL) 10' Lengths of EMT 23 pcs. You will need an area about 55' Long & 17' 6 Wide for your frame and an additional 10' at each end for the support ropes.

That you mark off this area before starting. Lay out two of the 3-way corners (A) 14' apart at one end, where your frame will be, with the 4 corner piece facing toward the other end of the frame. Measure 55' from the first 3-way corners (A) to the other end of the frame and lay out the other two 3-way corners (A) with the 4 corner piece facing the other end of the frame. Lay out the 4-way arch corners (B) between the end 3-way corners (A) so that they are about 14' apart. Assemble the five arch tops by attaching one 10' length of EMT (CL) to a 28 pipe (D) and insert a self drilling screw (J). Attach (D) to a 16 pipe (C) and insert a self-drilling screw (J).

Assemble the arch legs by attaching one 10' length of EMT (CL) to one 28 pipe (D). Insert a self drilling screw (J) at the joint. Complete assembling the arches by attaching the arch tops to the corners. Proceed to attach the legs to the corners of each arch.

Attach end caps (I) to the bottom of the frame legs. Assemble the eight runners, that go between the arches, by attaching one 10' length of EMT (CL) to a 52 pipe (G). Insert a self-drilling screw (J) to the 10' (CL) and the 52 pipe (G) joints. Stand up one end arch and attach a 14' runner to each of the end corners.

Stand up the second arch and attach the runners to it. Proceed to stand up the remaining arches and connect all the runners.

Your frame should end up being about 55' long. HANGING YOUR BATTING CAGE NET. Lay out your batting cage inside the frame and find the three ropes on top of the cage at one end. Proceed to attach the ropes to the arch top at one end of the frame. Then attach the three ropes, at the other end of the batting cage, to the other end of the frame.

Attach the net hangers (H) to the runners of the frame, about four feet apart, by laying the rope end over the pipe and inserting the carabiners through the loop. Then attach a net hanger to the middle of each arch. Start at one end and lift up one side of the net and attach the net hangers to it by clipping the carabiner to the rope along the top side of the net. Attach the middle of the net rope, below the arch tops, to the middle of the arch tops. Lift up the other side of the net and attach it to the runners the same way as #3.

Tie the four rope tails on the batting cage to the bottom of the end arches to prevent the wind from blowing the net inward. Buyers Who Bought This Item Also Bought. Steel Aircraft Cable Wire Rope.